Muzzleblasts

Editor’s Message | Muzzle Blasts Vol. 81, #5

The following article appeared first in the January 2020 Issue of “Muzzle Blasts Magazine”, the official magazine from the National Muzzle Loading Rifle Association.

Happy New Year! It is always exciting to greet January 1st as it holds all of our dreams and expectations for the coming months. New muzzle loaders to sight in, new loads to explore, and new hopes for Longhunter adventures are just but a few of our wide-eyed hopes. And here at the NMLRA we look forward to the many opportunities to serve our membership through black powder shoots, rendezvous, educational programs, seminars, shooting and sighting in at our world class ranges, and of course our two gatherings during the national shoots. Moreover, our Muzzle Blasts staff can’t wait to bring you the best stories and columns full of muzzleloading equipment; muzzleloading rifle/pistol/shotgun building tips; history; treks; hunts; primitive camping/cooking; trips beyond Friendship and insight into the best information from our muzzle loading culture.

To improve our arrival of monthly MB magazines, we are asking our magazine writers to get their articles/photos to us a week ahead of the previous deadlines. In other words, submit your material by the 25th of two months prior to publication. This allows the USPS time to get the magazines to the members by the 1st week of the month. If you would like a new schedule for submissions, email the office and we will reply with a schedule.

Our old friend (and past editor) Eric Bye brings sage advice to this New Year Muzzle Blasts with his article “Charge!” He writes, “I just bought a dandy antique gun that needs some TLC. At home the first thing I did was remove the barrel from the stock, insert a wooden ramrod as far as it would go, mark it with a pencil at the muzzle, and lay the rod along the outside the barrel to see if it reached all the way to the breech plug face. It stopped almost an inch short, so I re-measured to confirm. Sure enough: there was something inside that barrel.” Obviously, checking the inside of a muzzleloading barrel is not as easy as with a modern gun. But there’s nothing difficult or technical about it, and this article will reinforce the wisdom of making sure there is no charge lurking inside the breech.

Clary Estes brings a heartfelt story to our souls with a story about Rifle Number 42. Growing up with the idea that a gun was equal to art work seemed odd to my peers, but in my house it was always understood. “It’s country boy art is all I can tell you,” my father, Wayne Estes, a talented gun maker in his own right, once told me, but these were no ordinary guns. These were guns that took 60–160 hours to make. They were guns that were meticulously handcrafted by artisans who had spent decades honing their craft. These guns were heavy and loud, shooting off a KA-PANG of smoke with the pull of each trigger, before needing to be cleaned and carefully reloaded with hand molded round lead bullets for their next shot. These were guns that tied men to their American ancestry. These were long rifle muzzleloaders, the guns of colonial America.

There are so many great articles in this issue that it will be hard to decide which to start with first. But if you are me, I always read from the back to the front and am never disappointed. In “Beyond Friendship,” Jim takes us to Union City, Tennessee to visit with the iconic business that gave many of us a nudge down the muzzleloading trail. Dixie Gun Works was officially started in 1954 by Turner Kirkland. He started it as a hobby to make extra money while working as a traveling jewelry salesman after World War II. He would travel from town to town visiting stores to sell jewelry but would ask about any antique guns and gun parts. He bought sold and traded antique muzzle loading gun parts and his car trunk until it became full. He placed a small ad in Muzzle Blasts magazine in October of 1948. He placed a three inch ad at the cost of $3.50; he would make $16 from the orders and his wage as a salesman at the time was $20.00 a week. From there Turner Kirkland’s business would grow and continues to grow until his death on July 26, 1997. Dixie Gun Works has an over 600 page catalog which is loaded with a lot of information. The catalog isn’t just about what is for sale, but it also has a large section with reference tables covering service loads of muzzle loading rifles to muzzle loading cannons; weights and measure tables, including drams to grains to ounces. I always make sure I have a Dixie catalog at my desk.

And if your imagination hasn’t run wild yet, you need to pay attention to Bob Copner’s “The Campaign Horns of Copner!” Yes, this is our Bob Copner who serves as our 1 of 1000 Endowment Fund Chairman. Bob has put together a memorable article detailing how campaign horns had another place in the history of American campaign powder horns . . . in Vietnam!

Bill Carter, Editor of the HCH Horn Book, has given us permission to reprint The Campaign Horns of Copner following the American tradition as it is dedicated to the men and women who have served, or are serving honorably in the Armed Services of The United States of America, especially those who were wounded or WHO gave their lives for their country. The intent of this article is to document that the long- standing American tradition of creating a powder horn, while serving in the military in time of war, was continued in the 20th Century. Copner is quoted, “On July 25, 2009, the powder horn that I made and scrimshawed in 1972, at Ubon Royal Thai Air Force Base (RTAFB), Thailand, while flying a combat tour with the United States Air Force, was awarded the Madison Grant Award at the 2009 Gunmakers’ Fair at Dixon’s.”

Keep yer powder dry!

Dave Ehrig

Hunting the Prarie Wolf - Muzzle Blasts Archives

By Jim Van Eldik

    No that’s not a misspelling; that’s the way the original “Prarie Wolf” chronicler, William Clark, of the famed Lewis and Clark Expedition, referred to them. Though commonly referred to a “coyotes” these days, in honor the Corps of Discovery boys they will be referred to them by the more dignified Prarie Wolf title.

    One might ask, “Why would anyone want to hunt these discreditable creatures?” Admittedly this is not the type of game one normally thinks of for “harvesting” purposes. However, two reasons come to mind. In the dead of winter, these otherwise scruffy, down-at-the-heels looking creatures take on a more agreeable look. A thick whitish grey winter coat sprouts out on their emaciated carcasses admirably suitable for collars and fur hats.

    Second, the Prarie Wolf is one of the most entertaining and challenging game animals one can possibly hunt. I’m convinced in takes little more than a year for a Prarie Wolf’s IQ to surpass that of the average hunter’s - along with his sense of humor (more on this later). However, a successful hunt can be done. What follows will provide you with some sound information on how to hunt these wiley creatures, plus a personal sampling on how one might go about “blowing the shot.”

    A word here on the “where” of Prarie Wolf hunting. For starters - everywhere. Begin by looking under your front porch. To say the least, these little wolves adapt, and are comfortable living close to humans. As far as concentrations go, look first where there is a ready food supply, either carrion, or small, stupid animals. Let me interject here that one of the premier hunting grounds for these varmints used to be Los Angeles -- in particular West Hollywood and Beverly Hills. Here the mangy critters found a rich diet via a ready supply of small dogs (poodles) for their dinner menu. However, things are changing. As of late the movie people are wising up and equipping themselves with antiyote dogs - like Dobermans and massifs. Los Angles is no longer the hunting ground it used to be.

    A note here on using dogs for the hunt. The Prarie Wolf has a peculiar rocking/bounding gait when coursing across the prairie, each bound encompassing about five yards. It also has superior canine stamina. No domestic dog can match the Prarie Wolf’s speed or endurance. However, that doesn’t mean there will not be a chase. Once pursued by one of its canine cousins, the Prarie Wolf, of pure avarice, will slacken its pace maintaining just enough interval to keep the dog committed. By glancing back now and then it will know precisely when the dog’s heart is about to burst, and when it does, little wolf instantly disappears (more on this later).

    Anyway, back to hunting areas, probably the best hunting ground, and the one I always used, is in central Nebraska, viz., the old Oregon Trail. This Prarie Wolf Shangri-La was established by the trail of dead oxen left behind during the post Forty-niner migration west. Yes, the Little Wolves love carrion. In fact it has been asserted that they will eat anything up and including nitroglycerin.* However, this is not true. A Prarie Wolf WILL NOT eat another Prarie Wolf.

    Anyway, central Nebraska still maintains a large Prarie Wolf population. For dietary purposes the oxen carcasses have mostly been replaced by potato chip bags and Pepsi cans tossed out of cars along I-80. They will also eat an occasional newborn calf -- thus, Little Wolf hunters are welcome guests at most central Nebraska farms and ranches.

    As far as armament goes, one might question the use of muzzleloaders for hunting such an elusive game. Well let me say right off that William Clark was perfectly content blasting the Upper Missouri Prarie Wolves with an 1803 Harpers Ferry flintlock rifle. My friends and I have employed a variety of traditional armament including the Numrich swivel breach (providing two shots of course), the T/C Renegade, the Tennessee rifle, and stretching the idea of muzzleloader a bit, the Sharps percussion. This is not the handicap you would think. Almost without exception, every successful hit my friends and I have gotten on the critters has been on the first shot. And virtually all were at a hundred yards or less. Much of the hunting is done via “push” in which case the new lightweight in-lines make a perfect Prarie Wolf gun. 

    Admittedly most of the Prarie Wolves bagged in the hunting magazines are enticed in using “calls.” My friends and I always relied on the old “dying rabbit” call where one blows through a plastic tube producing a sound similar to the noise makers heard on New Year’s Eve. This call works, but it will only work once; the Prarie Wolf has a wonderful memory. These days there seems to be a preference for electronic devices. One of the most popular is called the “Banshee” which I understand uses a recording of Hillary Clinton’s laugh. The downside to calling Prarie Wolves is you never know the direction from which they will approach. One night, while waiting for the Little Wolves in a fence row, I was approached by a herd of cattle on the reverse side of the fence. They came within six feet of me making a terrible racket on the corn shucks. I was not able to observe the cattle due to the thick grass and weeds in the fence row. Later the guys informed me there were no cattle in the field -- it was a actually a lead footed Prarie Wolf sniffing me out. Had I brought my bayonet along I might have taken him with that.

    I have to say I always enjoyed the “sweeps” best. Trekking the wild and wooly Nebraska Sand Hills offers a chance to enjoy the terrain as well as hunt. It also provides a chance for adventure. I recall the time I was hiking along the slope of one of the hills and came to a patch of snow. I started across and immediately plummeted straight down into the snow only stopping my plummet by extending my arms. The snow hid a precipitous ravine I had to swim out of.

    Our “sweeps” composed three or four of us walking abreast encompassing about a half mile interval, and then simply hiking across the prairie. This approach provides lots of action, but not necessarily a lot of “harvested” Prarie Wolves. I recall in one of our early hunts a Prarie Wolf “busted” on the far right. He then passed in front of each of us in turn while we took our best shot at him. Upon completion of his successful run, and safely out of sight, he lit up in joyful song (laugh). Most embarrassing!

    In another incident, while shadowing a deep ravine, my “sixth sense” detected a Prarie Wolf lurking below. I kicked a clod of dirt into the Wolf’s likely hiding place, and out he came. I touched off one of my usual misses as the Little Wolf shot down the ravine. He eventually reached the valley below where he pulled up directly behind one of my friends standing on a knoll, peering off in the opposite direction. The Little Wolf eventually finally my friend and reversed course making off for parts unknown.

    This incident illustrates another point; these fur balls have a terrible time detecting stationary hunters, which accounts for the one adorning my vest in the illustration. This one did the “circle around” drill they habitually use and came directly at me, even though I was standing totally in the open -- but standing on snow in white coveralls.

    A final warning about hunting these critters, best explained with another illustration. I “nicked” a Prarie Wolf one time, and set off following his tracks and blood trail. He was not badly hit, so the trail went on and on and on. Eventually ANOTHER hunter of unknown origin began following the wounded animal. I was unhappy with this, but when a THIRD hunter joined the hunt I was irate. After a while it dawned on me that the boot prints I was following seemed very similar to mine. So I did a comparison and found they WERE mine. I was tracking the Prarie Wolf in a big circle. So I a took another turn around the circuit looking for the exit. There was none! Apparently the Prarie Wolf either ascended, or descended, or employed some other phantasmal move.

    Prarie Wolf hunting is not for the milquetoast.


* See Roughing It by Mark Twain.  

This article was originally printed in Muzzle Blasts Magazine. A digital archive of every Muzzle Blasts magazine is available online to all NMLRA members

NMLRA.org

Muzzle Blasts on Instagram
NMLRA on Facebook

NMLRA on Youtube

Muzzle Blasts Podcast   

      

           

The Ashley Hawken Part I - Muzzle Blasts Archives

By Bob Woodfill

The Ashley Hawken was built specifically for General William Henry Ashley, by Jacob and Samuel Hawken, to defend his keelboats from hostile Indians, as the fur traders went up the Missouri River to establish trading posts. The rifle needed to be capable of shooting farther than the trade guns used by the Indians, who would often shoot down from the overhanging banks along the river, as the keelboats passed. Therefore, a ‘Super Hawken’ was built that could throw a one ounce ball with accuracy beyond 200 yards.


The year was 1822. General Ashley and his partner William Henry, had placed the famous advertisement in the St. Louis newspaper on February 13, for “one hundred enterprising young men, to ascent the Missouri River to its source and be employed for one to three years trapping for furs”. The men who responded to the ad eventually became the who’s who of the American fur trade, including such greats as Jim Bridger, Hugh Glass, Jedediah Smith, William Sublette, David Jackson, James Clyman, Jim Beckwourth and Thomas Fitzpatrick

In April 1822, Henry and the free trappers, who responded to the newspaper advertisement, ascended the Missouri River to the mouth of the Yellowstone River in a keelboat, and later established Fort Henry near the Montana-North Dakota state line. A second boat with their supplies for the winter left St. Louis one month later, but sank only 300 miles up river from St. Louis. A dispatch was sent to General Ashley in St. Louis who in 18-days, obtain credit and assembled another supply boat. This time Ashley went with the supply boat and arrived at Ft. Henry in October. Able to supply the fort, he left Fort Henry and returned to St. Louis to prepare for the 1823 season.

Keelboats, which displaced only about two feet of water, were often used by the fur traders on the shallow waters of the Missouri River. They were usually from 40 to 80 feet long, and were built with a strong central keel that helped deflect obstacles in the shallow water. Except for a rare day in which the sail was useful, they were either rowed, poled or pulled upstream by the crew of 20 to 30 men. 

Swivel cannons were often utilized on river boats for short-range defense. They ranged from 18” to 36” in length and had a smooth bore from one to two inches in diameter. This bore was quite suitable for a hand-full of musket balls, but only effective for short-range defense. The Lewis and Clark Expedition of 1804-1806 had a swivel gun mounted on the bow of their keelboat by Captain Clark, but it was never used. 

It was probably during the winter of 1822/23, after returning from his first trip up the Missouri River, that General Ashley commissioned the Hawken gunsmithing shop to build a Super Hawken, to help combat the continuing harassment of his keelboats by the Indians. The gun was to be designed for long-range shooting, and capable of reaching with accuracy the numerous river bluffs, which lie above the Missouri River.

We know only three things for certain about the Ashley Hawken from information given in a 1882 newspaper interview with Sam Hawken. First, it was built by the Hawken shop for General Ashley. When Sam Hawken gave the newspaper interview, he was 90 years old, and was very ‘inclusive’ in his remembrance of the early years. In 1821 Jacob was listed in the first city directory as a gunsmith. Sam arrived in St. Louis on June 3, 1822, a year later. Sam simply recalled that “We supplied the gun to Ashley”.

I don’t believe that it has been pointed out before, but this rifle would have been J.&S. Hawken rifle Serial #1, or the first rifle built with the combined talents of both Jacob and Samuel Hawken. In the newspaper interview, Sam called it a “Super Rifle”, because it fired a one ounce ball from a three and one-half foot long barrel. These basic specifications leave considerable room to speculate about all of its features, but some other clues can help us determine its probable configuration.

Jacob Hawken came to St. Louis in 1819, after working from 1808-1818 at the Harper’s Ferry Arsenal in Virginia. He was very familiar with the strong and weak features of the U.S. Model 1803 Harper’s Ferry rifle and later models of U.S. Government rifles. He watched as brass fittings gave way to stronger steel fittings. The caliber of the Government models was increased to 69-caliber to extend their effective range. The barrels of the latest 1821 Models were round and a full 42” long.

.

When Jacob Hawken came to St. Louis, he and James Lakenan, another gunsmith who had worked at the Richmond, Virginia armory, shared a log house from 1820 to 1825. Jake, and later Sam, were both influenced by the Virginia gunsmith James Lakenan, and the iron-mounted rifles which originated from the Virginia region on the east coast. The Super Hawken that was to be built for Ashley would naturally be the product of Jake Hawken and James Lakenan’s experiences during their many years working at the armories.

A fourth, and often unmentioned feature of the Ashley Hawken, is that it was a flintlock. Irrespective as to when the percussion cap was originally invented in Europe, they were first seen on the east coast in 1825/26, and later first advertised for sale in St. Louis in 1831. The Ashley Hawken predated the introduction of the percussion cap in the St. Louis area, and it was a flint ignition rifle. Because of Jake’s familiarity with the 1803 through 1821 U.S. Government rifles, he would have probably chosen one of the large and dependable flint locks that were used on the U.S. Springfield musket models.

As reported in the August, 1976 issue of the The Buckskin Report, there was an earlier attempt to build a rendition of General Ashley’s 69-caliber flintlock Hawken. Such notables of the time combined their talents to make John ‘Dinglehoofer’ Baird a copy of Ashley’s Hawken. They were Andy Baker (stockmaker), Bill Large (barrel maker), Tom Dawson (flintlock), Bob Roller (triggers), Jack Haugh (trigger guard), Bill Fuller (buttplate), Randy Cochran (wood) and Tony Lageose (engraving). The finished rifle weighed 11.75 pounds and boasted a 37-1/2” long octagonal barrel with a thickness of 1.1875” at the breech and 1.0625” at the muzzle. The full-stocked rifle was exhibited and fired at Friendship, IN with a 0.690” diameter round ball, a 0.016” thick denim patch, and 160 grains of GOI 2FFg black powder. Its power and recoil were impressive…!

Pictures of this rifle shows its styling be more representative of an early J.&S. Hawken full-stocked rifle with iron fixtures. I believe that a better interpretation of the original rifle can now be made. Before starting my recreation of Ashley’s Super Hawken, I consulted with Don Stith, Bob Roller, and other Hawken bugs of today. The following is my reasoning for selecting the rifle’s basic components.

Caliber--In Sam Hawken’s 1882 newspaper interview, he says that Ashley’s Hawken threw a one ounce ball. Technically, a one ounce ball would weigh 437.5 grains or be about 0.660” in diameter. In the literature, I have seen the caliber quoted from everything from 66 to 69-caliber. The U.S. Springfield Musket--Model 1821, the last flintlock musket procured by the U.S. Army, was a 69-caliber smooth-bore. I believe that Sam’s reference to a ‘one ounce ball’ would refer to the 69-caliber ball which was the norm of day, and used in the most advanced long-range muskets made prior to 1822.


Barrel--According to Sam Hawken, the barrel was three and one-half feet (42”) long, or the same length as the U.S. Springfield Musket--Model 1821. This length of barrel would be required to get adequate velocity from a 69-caliber ball for long-range shooting. To obtain the accuracy required at 200 yards, the barrel would have had to be rifled. Jake knew that an octagonal barrel was stronger than the round barrels that were used on the the U.S. muskets, and as a bonus, it would add some weight to the rifle to lessen felt recoil.


Lock--I believe that Jake would have used a flint lock similar to or taken off one of the U.S. Springfield Model 1803 to 1821 models. They were large and dependable--using a large musket-sized flint to produce a massive amount of sparks. These locks utilized a reinforced hammer to strengthen the hammer, hereby giving a smaller chance of breakage with repeated, hard use.


Buttplate--I believe that Jake would have used a flat iron buttplate as was standard on the military models. A flat buttplate would have lessened the effects of felt recoil much better than the crescent-type buttplates used on Kentucky and later Hawken rifles.


Triggers and Guard--I believe that Jake would have wanted to incorporate a double-set trigger system on the rifle to enhance precise shooting at the longer distances. To accommodate the double-set triggers, an English-style trigger guard with a large bow was probably used.


Stock--The U.S. Springfield Model 1821 used a full-length stock with its 42” barrel. Jake would have given the stock a more Tennessee-type stock design with a thinner wrist to incorporate the double-set triggers, all in combination with a long tang for added strength. Either American walnut or maple would be suitable. A small patchbox similar to the 1803 Harper’s Ferry, but made of steel, would be appropriate for that period and for the Rocky Mountains!


In Part II, I will detail the construction of a rifle to match the known and proposed features of the Ashley Hawken.

This article was featured in Muzzle Blasts magazine in July 2017. A digital archive of Muzzle Blasts magazines from 1939 to present is available to all NMLRA members.

NMLRA.org

Muzzle Blasts on Instagram
NMLRA on Facebook

NMLRA on Youtube

Muzzle Blasts Podcast












A Most Terrible Musketry: The Battle of Kernstown

By mid-afternoon of March 23, 1862, the crossroads hamlet of Kernstown, Virginia was nervously eyed by the Confederacy's Valley Army.  Under the command of Major General Thomas J. Jackson, the Rebels had been on the run for the previous eleven days and were eager to turn the tables on their Yankee pursuers.  Better known simply as "Stonewall", Jackson had earned his nom-de-guerre for tenacious fighting at the First Battle of Mannassas in July 1861. A West Point graduate and former professor at the Virginia Military Institute, he combined his professional training with an innate tactical ability that eventually earned him a near perfect battlefield record.  His unconventional genius for strategic operations, still studied today in military academies across the globe, ranks him as one of the greatest soldiers in American history.

    But in the fight that was to unfold on the fields and hills of Kernstown, Jackson was faced by the most unlikely of opponents.  Though two Federal generals were within minutes of the battlefield, command of Union forces devolved, through an unlikely turn of events, on an obscure Hoosier colonel with limited combat experience.  Fated to confront the legendary Stonewall, and the greatest challenge of his life, was an affable citizen soldier from Martin County, Indiana - Nathan Kimball.

    Born in Fredericksburg, Indiana on November 22, 1822, Kimball possessed both ambition and a keen intellect that early marked him for leadership.  Graduating from Indiana Asbury College in 1841, he briefly supported himself as a schoolteacher before settling on a medical career.

    By 1845, Kimball had taken a degree at the University of Louisville, married, and settled in Washington County where Kimball opened a thriving practice.  His successful career as a country physician, however, was put on hiatus by the outbreak of the Mexican War in 1846. Kimball, already a highly respected member of his community, raised a company of volunteers and led the men to war when they were assigned to the 2nd Indiana Infantry.

    The young captain gained valuable experience during Zachary Taylor's campaign in northern Mexico, but the regiment's performance at the Battle of Buena Vista on February 23, 1847 proved an embarrassment that would haunt the state for decades.  In the face of an impending Mexican bayonet charge, the green troops of the 2nd panicked, fled in disorder, and virtually unhinged the American line.  A near disaster was averted by the likes of Kimball, who desperately attempted to rally the remnants of his company.

    Despite a hard-fought American victory, the conduct of the 2nd, considered scandalous during the aftermath of the war, was a source of much recrimination.  Ultimately, blame for the regiment's collapse fell on its commanding officer, Colonel William Bowles of Orange County; the regiment's junior officers, including Kimball, largely escaped the imbroglio with their reputations intact.

    Following the war, Kimball moved his practice to Martin County and clumsily threw his hat into the political arena.  A member of the defunct Whig party, Kimball lost an election to the state senate in 1847, and likewise failed in his bid for a seat at the electoral college in 1852.  When the Republicans formed in 1854, Kimball cast his lot with the new party.

    The ascendancy of the Republicans in the 1860 presidential election of Abraham Lincoln proved a watershed event for a divided nation, and the subsequent secession crisis and outbreak of civil war once again saw Kimball don a uniform.  As he had in 1846, he raised a volunteer company from Martin County and was elected its captain. He was, however, quickly commissioned colonel of the new regiment, the 14th Indiana.  Kimball not only had the right political affiliation for such an appointment, he was the only officer in the regiment to possess any appreciable military experience.

    Largely recruited from the farmhands and laboring class of southwestern Indiana, the regiment was woefully ill prepared for active campaigning.  The enlisted men were entirely unaccustomed to military discipline and the regiment's officers, elected from the ranks, were little better. Kimball had a scant two months in which to train his men before they were ordered to the front in July 1861.

    Assigned to the rugged hills of western Virginia, the 14th spent several miserable months operating against rebels on Cheat Mountain, but the haste of pressing the poorly trained Hoosiers into action soon told.  Unseasonably foul weather and plain homesickness combined to drain the spirits of the inexperienced soldiers; by the end of August, morale was considerably degenerated   Stirred by a handful of malcontents, the men fell under the delusion that they could not be held in the service past three months and a virtual mutiny was threatened. A semblance of order was restored following a disciplinary crackdown which included a handful of courts-martial.

    Despite the rough start, Kimball transformed his rough-hew Hoosiers into real soldiers over the following winter.  The troops proved adept at complaining - the eternal prerogative of the soldier - but Kimball rarely became the object of their ire.  "He is a meticulous soldier," observed one private, "and he loves his men, and they all know it, and so they love him." This sincere concern for their welfare inspired a trusting devotion from the men who, it was said, "would follow him anywhere and anytime, and against any odds."  Such sentiment would be desperately needed the following year.

    The spring of 1862 saw an ambitious Federal attempt to end the war by one great thrust for the Confederate capital. Major General George McClellan, commanding the Army of the Potomac, devised a grand plan to seize Richmond not by an overland campaign but by a massive amphibious operation that would unexpectedly threaten the city from the east.  President Lincoln gave grudging approval to the operation on the emphatic condition that McClellan would make certain the defense of his own capital and, in the president's words, "Leave Washington secure."  McClellan consequently ordered his army's V Corps, then stationed in the Shenandoah Valley, to position itself in northern Virginia and thereby cover the approaches to Washington.

    Events in the Valley seemed to favor such a move.  In the first week of March, V Corps commander Major General Nathaniel Banks had moved against Stonewall Jackson's Valley Army and forced the Confederates to evacuate Winchester, the most vital road hub in the northern Shenandoah.  With the outnumbered Rebel army on its heels, it was thought safe to transfer the V Corps toward Richmond. 

    Jackson was equally determined to forestall such a move.  Under orders to keep Federal troops in the Shenandoah from cooperating with McClellan, Stonewall acted quickly when, on March 21, he was informed that the V Corps appeared to be headed out of the Valley.  "Apprehensive that the Federals would leave this military district", he wrote, "I determined to follow them with all my available forces."  

    The V Corps' exit from the Valley was indeed imminent.  General Banks, in making preparations to move his command, was likewise of no mind to leave the northern Shenandoah wide open to a Confederate thrust, and he stationed his 2nd Division, under Brigadier General James Shields, in the environs of Winchester.

    On March 22, the vanguard of the rebel army appeared at Kernstown, about two miles south of Winchester.  Shields deployed troops to counter what he considered to be a mere Confederate demonstration, but while reconnoitering that evening was unexpectedly struck by shellfire.  Rushed back to Winchester, army doctors discovered that the general's left arm was broken, his shoulder and side painfully injured, and he struggled to remain conscious. While Shields lay in bed, he passed command of the division to his senior brigade commander, Colonel Nathan Kimball.

    Kimball, though he had yet to receive a brigadier's star, had been advanced to brigade command that winter.  However, at daybreak on March 23, 1862, the unassuming Hoosier officer had barely commanded more than a company of men in pitched battle.

    It was a Sunday morning, and most Union troops expected an uneventful day in camp.  Shields, slowly recuperating in Winchester, conferred with Banks and both agreed that the previous day's fight had merely been the result of an unimpressive rebel cavalry probe.  Banks made plans to leave town that afternoon.

    When fighting resumed around 9:00 A.M., Kimball confronted the Confederate skirmishers and quickly consolidated his own position around Pritchard's Hill, an eminence that commanded the Valley Turnpike, the area's primary north-south thoroughfare.  From his sickbed in Winchester, Shields encouraged Kimball to press forward from his Pritchard's Hill position and drive in the enemy skirmishers, admonishing that "there is no force before you but that we encountered the other day."  

    Kimball demurred.  Sensing that a greater Confederate force was in the area, he called up the rest of the division to bolster his Pritchard's Hill line and maintained a defensive posture.  For three hours, Kimball sparred with the Confederates in his front and refused to budge.

    By 1:30, Shields grew exasperated with the static situation and forwarded yet another order for Kimball to press the attack.  Convinced that the enemy had not yet shown his "real strength", Kimball made the decision to disobey Shield's direct order. He later explained that the general could not possibly "comprehend the situation, the strength of the enemy, nor the positions held by the respective forces, and satisfied that from his bed in the city five miles to the rear he could not properly conduct the movements which might be required by the exigencies of the situation, I determined to remain on the defensive and in the position now held by my line."  

    Kimball's caution was not misplaced.  Soon after he refused Shield's second order, the bulk of Jackson's force made its appearance two miles to the south.  Surprisingly, the famed Confederate commander never intended to launch an attack that morning. An intensely devout Presbyterian, Jackson was entirely disinclined to give battle on the Sabbath, but following erroneous reports that he was opposed by just one Federal brigade, he felt obliged to throw his entire force into the fight and dislodge the Federals from Pritchard's Hill.  The pious Jackson offered an apologetic explanation of his decision to hit the Federals on the Lord's Day. "Important considerations," he explained, "rendered it necessary."  

    He was, however, not foolish enough to approach Pritchard's Hill head on.  Moving his troops west of the turnpike, Jackson aimed for a low ridge that angled southwest to northeast.  Known to locals as Sandy Ridge, the position dominated the surrounding terrain, including Pritchard's Hill, and led menacingly to Kimball's right and rear.  When Confederate artillery unlimbered on the ridge and began lobbing shells on Kimball's position, the colonel realized he had been outmaneuvered and was in a precarious position.  He immediately began shifting troops for a desperate assault on Sandy Ridge.

    Oddly enough, both Kimball and Jackson labored under erroneous assumptions regarding his opponent's strength.  Kimball, with roughly 5,000 men at his disposal, grossly overestimated Jackson's force as exceeding his own. Jackson, commanding under 3,000, badly underestimated the Yankees at just one brigade, not an entire division.  When one of his staff officers finally observed the bulk of Kimball's force and reported the error, the imperturbable Stonewall greeted the shocking news with characteristic calm. "Say nothing about it," was his response, "we are in for it."  

    As the fight developed, both sides were in for a severe mauling.  The farm fields that crowned Sandy Ridge were crisscrossed by a network of stone and rail fences that offered a marked advantage to any defender.  Jackson, finally realizing that he was outmatched and therefore incapable of seizing Winchester, contented himself with holding his position until he could withdraw his forces after nightfall.

    At approximately 4:00 P.M., the first Federal troops launched their assault on Sandy Ridge.  Advancing in the face of determined Confederate troops who were well protected behind a stone wall, the Union men braved a withering fire and were felled by the dozens.  Kimball dispatched further reinforcements to bolster the attack, but regiment after regiment stalled in front of the ready-made Confederate breastworks. Having been forced to hurriedly shift their position near Pritchard's Hill in order to deal with the rebels on Sandy Ridge, the Federals largely went into action piecemeal.  In the confusion of the fighting, their disjointed attacks failed to take full advantage of their numeric superiority.  

    Despite the high cost in lives, the attack slowly succeeded in weakening the Confederate lines.  In order to counter the mounting pressure from Kimball's troops, Jackson was forced to extend his line further toward the Valley Turnpike in order to protect his right flank.  Stonewall's maneuvering succeeded in blunting continued Federal attacks, but in the process his own lines were stretched to the breaking point.

    The fierce fighting on Sandy Ridge shocked the most experienced of troops.  Civilians in Winchester were horrified by the sound of battle. A “most terrible and long continued musketry" one described it, "not volley after volley, but one continued fearful roll."  Kimball noted the raging "fury" of the battle and even Jackson, a grizzled veteran with two decades of experience, said that he did not recollect "having heard such a roar of musketry."  

    By 5:00 P.M., such brutal fighting had produced little more than a bloody stalemate.  The armies had grappled for over an hour with few results other than dead and wounded men.  Determined to break Jackson's lines before nightfall, Kimball ordered one of his last unbloodied regiments toward the inferno on Sandy Ridge: the Hoosiers of the 14th Indiana.

    Subsequent to Kimball's promotion to brigade command, leadership of the regiment fell to Lieutenant Colonel William Harrow.  A Knox County attorney, Harrow possessed a brash, no nonsense personality that failed to earn him the affection of the men in the ranks.  Destined for divisional command before war's end, the hard-driving Harrow laid the foundation of an aggressive command style as he led his 450 men at the double-quick toward the firing line.

    As the troops mounted the slope of Sandy Ridge, the entire hillside was shrouded in gun smoke.  When what seemed to be gray clad soldiers appeared to the front, the jittery Hoosiers opened fire.  A lone figure darted toward the regiment, frantically calling on them to hold their fire; in the confusion, they had inadvertently opened up on the rear of the 5th Ohio.  The Buckeyes' commander, Lieutenant Colonel John Patrick, urged the Hoosiers to the left, where, he shouted, they would meet with "plenty of secesh."

    The regiment wheeled into action on the extreme left of the Federal line.  Determined to do their duty, the men "marched up to their places as deliberately as if on drill."  At the first Confederate volley, the regimental standard bearer fell. His companion who carried the national flag then lifted and waved both banners, only to be shot down "in about two seconds."  

    Men began to fall, and one soldier thought that the sound of bullets slamming into his comrades was eerily similar to the sound of beating carpets clean back home.  The 14th Indiana had entered a maelstrom.  About 90 yards to the front, "a long wreath of blue smoke settled over a low stone wall," recalled one Hoosier, "out of this a fire flashed constantly.  Between our line and this wall the dead and wounded lay in heaps." Harrow's soldiers faced the grim brutality of combat in different ways. Some, paralyzed with fear, fell to the ground; most stoically stood their ground and exchanged fire with the enemy.  But in a singular instance of personal heroism, the actions of a private from Company G would alter the course of battle.  

    Paul Truckey, a carpenter from Vincennes, leapt forward, and, waving his rifle aloft, cried out "Come on, boys!"  He then sprinted "headlong after the rebels as a dog would chase a rabbit, loading and firing as he went."  Galvanized by Truckey's action, a number of voices were heard to cry out "forward" and the entire regiment spontaneously dashed for the rebel line.

    When the Yankees were within twenty yards of the stone wall, Lieutenant Colonel John Patton of the 21st Virginia received, virtually simultaneously, a withdrawal order from his brigade commander.  Having already been worn down by repeated Federal attacks, the rush of oncoming Hoosiers was more than the Confederates could withstand.  Finally released from the fight, the Virginians scattered from the ridge.

    The flight of the 21st Virginia, which occupied the extreme right of Jackson's army, exposed his flank and caused a general collapse of his battle line.  Kimball's entire division then pressed its advantage and closely pursued the enemy. Federal units became hopelessly mingled in the confusion and Captain Elijah Cavins of the 14th Indiana recorded that "The Confederates fell back in disorder, and we advanced in disorder just as great, over stone-walls and over fences, through blackberry-bushes and undergrowth…brigades, regiments, and companies advanced in one promiscuous, mixed, and uncontrollable mass.  Officers shouted themselves hoarse in trying to bring order out of confusion, but all their efforts were unavailing."

    The retreating rebel army retired slowly and "continued to make it very hot for our men," rallying "in every ravine and behind every hill - or hiding singly among the trees."  A complete rout of Confederate forces was averted by such stubborn fighting, and nightfall enabled Jackson to withdraw his battered army from the field.

    A frightful price had been paid for the northern victory.  Jackson reported a total loss in killed, wounded, and missing of 718; Kimball reported 590 casualties.  The 14th Indiana suffered 54 overall casualties. A Federal surgeon's memories of the ghastly battlefield sadly humanized such cold statistics.  "Oh, what a sight," he recalled, "legs smashed, heads torn off, faces mangled, arms shattered, pools of blood, bowels protruding, and every conceivable mutilation."  

    Ironically, Jackson's tactical defeat at Kernstown turned into a strategic victory for the Confederacy.  Alarmed by the rebel attempt on Winchester, Federal authorities immediately ordered Banks’ V Corps back into the Valley, frustrating McClellan's overall efforts to secure reinforcements for his Peninsula Campaign.  Over the succeeding three months, Jackson's Valley Army outmarched, outmaneuvered, and outfought its Federal opponents in a string of victories from one end of the Shenandoah to the other. Known simply as the Valley Campaign, Stonewall's brilliant generalship against overwhelming odds secured his place in the pantheon of America's military leaders.  The fight at Kernstown constituted the single instance in which the Confederate legend was defeated on the battlefield.  

    General Shields, who resumed command of the 2nd Division on April 30, initially gave Kimball credit for the victory.  Shields offered his thanks for Kimball's independent management of the battle, and commended the colonel "for his devotion to the interests and honor of the command and the signal service he has rendered it in this emergency."  

    At the same time, Shields was encouraging erroneous newspaper accounts of the battle that credited him with command at Kernstown.  His official report of the engagement was little more than an inaccurate and blatant attempt to personally capitalize on the victory.  In it he claimed to have been the mastermind of Federal strategy on March 23, and asserted that Kimball had simply "executed my orders."      Nathan Kimball naturally bristled at such fast and loose treatment of the facts.  In a letter to a friend, he insisted that "I had full command and planned and directed the movements of the entire fight in person…You will not wonder, therefore, that I am annoyed at seeing the garbled and false accounts that have appeared in the newspapers."  

    Kimball went on to serve with distinction through the remainder of the war, ultimately earning the rank of brevet major general.  Gravely wounded at Fredericksburg, he was nominated for lieutenant governor of Indiana in 1863 but refused the offer in order to stay with his men.  Later transferred to the western theater, he commanded troops at Vicksburg, Atlanta, Franklin, and Nashville.

    Following the end of the war, Kimball resumed his private practice and re-entered politics.  He became the first commander of the Grand Army of the Republic in Indiana, and served as state representative from Marion County.  In 1873 he was appointed Surveyor General of Utah Territory; briefly working as government physician at the U.S. Indian Agency in Fort Hall, Idaho, Kimball became the postmaster in Ogden, Utah, where he passed away on January 21, 1898.

    For Nathan Kimball, recognition as the only Federal officer to best Stonewall Jackson has proven somewhat elusive.  As a result of the false accounts of the battle that began circulating in the spring of 1862, most popular histories of the war, to this day, generally credit the victory at Kernstown to the bed-ridden and incapacitated General Shields.  Though often slighted by history, Kimball was always defended by his men. "The Hoosier soldiers love Col. Kimball," explained a member of the 14th Indiana. The victory at Kernstown “was won by our forces under Colonel Kimball.  The honor is his, and he should have accredited to him what his merit deserves."     

This article was originally printed in Muzzle Blasts Magazine. A digital archive of every Muzzle Blasts magazine is available online to all NMLRA members

NMLRA.org

Muzzle Blasts on Instagram
NMLRA on Facebook

NMLRA on Youtube

Muzzle Blasts Podcast    

     

   

   

NMLRA Membership Giveaway - Guy Kroll from "Rocklock Enthusiasts"

Good Morning. Its that time of year again for giving and thanks. This is our fourth year of giving away 6 memberships in the National Muzzle Loading Rifle Association. We do this to help the NMLRA grow and to give back to the great members of our page. Again this year my friends, Neil Eddington and Ian Egbert will be joining me in giving away memberships to the members.

We will be giving away 6 memberships this year, 2 from me 2 from Neil and 2 from Ian. As I am the admin for two pages, Rocklock Enthusiast and Flintlock Era, we will give 3 memberships to each page.

The rules are simple:

1. You must be a member of the page.( Rocklock Enthusiast and/or Flintlock Era )

2. You must not be a current member of the NMLRA

( we want to the winners to be new members to the NMLRA)

To enter all you need to do is " LIKE" this post.

All names will then be placed in a hat and the winners will be drawn from there.

Contest runs from today, November 19th to December 20th, this gives everyone the opportunity to enter at some point.

The drawing will be done around 6pm on Dec 20th.

Enjoy, Good Luck to everyone.

Guy Kroll


Making and Fitting Muzzle Caps. Part I - Muzzle Blasts Archive

By Fred Stutzenberger

There are many dealers out there who sell ready-made caps, but anyone who shapes one rifle to fit a muzzle cap must be a little touched in the head

    Of all the hardware used in the stocking of a muzzleloading rifle or pistol, the muzzle cap (or fore end cap on a halfstock) encompasses the widest range of materials and methods of manufacture. Most of the 17th Century wheel-lock rifles were capped with carved or scrimshawed bone, ivory or stag (3). The Germanic Jäger rifles of the 18th Century were often capped with horn, exotic woods or with highly decorative castings (Fig.1) of brass or gilded iron (4). The 18th-19th Century American fullstock longrifle was generally capped with soldered two-piece or swaged one-piece sheet brass (2) except in the Southern Appalachians where rifles were capped with hand-forged iron grooved for the ramrod or sometimes with bone (Fig. 2). 

    I remember seeing only two old original American halfstock rifles without a fore end cap (perhaps readers can help me out on that one). Most of the old halfstock rifles that I have seen were capped either with the common two-piece sheet metal cap a la’ the Hawken (Fig. 3) or caps cast of pewter, tin or other low temperature-melting (250-300oF) metal such as CerroSafe (see suppliers’ list). The ability to cast low temp metals into any conceivable cutout area generates some flamboyant designs (Fig. 4). British gunmakers of the late muzzleloading era were much more conservative in the capping of their fore stocks, using horn with a distinctly shaped schnabel (Fig. 5). 

    From the strictly utilitarian point of view, the purpose of the muzzle cap is to protect the vulnerable tip of the stock and prevent it from splitting. The simplest restraint to that purpose is a plain metal band (Fig. 6) wrapped around the fore stock an inch or two back from the tip. Cheap-but-sturdy trade guns were turned out by the thousands and peddled to the First Americans by the Hudson’s Bay and Northwest companies during the fur trade era (5). 

    Most of the muzzle caps on American longrifles were made of sheet metal (examples in Fig. 7). Making such muzzle caps is fun and rewarding if you are creative and experienced with working metals. If you are not, it is best to buy a commercially made cap if you can find a source for one that closely fits your barrel. Commercial caps are available in 1/16” increments from ¾ to 1- 1/8. If you find a cast brass cap that is very slightly larger than the muzzle, Keith Lisle (custommuzzleloaders.com) suggests carefully squeezing them a bit in a vise, then filed & shaped to fit a muzzle that is slightly smaller than the casting. Also, the cast caps are usually quite thick, thus you can square them off & make them appear as a hand made cap, rather than the rounded generic cap as it was cast. 

    In Part I of this series, the procedure for installing a commercial cap will be described. In Part II, with insight from Keith, we are going to show you how to make several styles of metal caps using different methods. Part III will describe the making of caps from horn and exotic wood.

    Before you decide, be sure that a muzzle cap is appropriate to your style and period of rifle or pistol. Some of the most elegant pistols I’ve seen (the best British, French and Flemish pistols come to mind) made their striking appearance sans muzzle caps. So if you have a commercial cap that is appropriate for your rifle or pistol, let’s get started.

    It is easier to get your commercial cap fitting closely to your barrel by taking the barrel out of the stock. With a barrel/cap combination of standard dimensions, fitting the cap to barrel is pretty easy. Usually they go together nicely with little filing. The fitting of the cap to the stocked barrel is a different matter.

1.Remove enough wood from the tip of the fore end to allow for the installation of the cap with about a 1/16-1/8” of the barrel protruding out beyond that. With the barrel clamped tightly in the channel, slide the cap onto the muzzle in reverse and press it up under the barrel for a tight fit. Pencil a line around the circumference of the cap onto the fore end. That will be the dimension of the cap when installed. Hopefully you have left enough wood on the stock to accommodate that.

2. Measure the inside length of the cap. It is easy to do that with an adjustable square. Add 1/8” to that measurement to allow for the thickness of the end cap and to allow a bit of barrel to protrude beyond the cap. Lock the square  and set the base against the muzzle. Draw lines on the side of the fore stock to determine how far back the wood needs to be removed from along the fore end (Fig. 8). Using a thin-bladed saw (a 24-tooth hacksaw blade works well), carefully make a series of shallow cuts around the fore end. Be careful not to saw into the barrel channel . . .that would seriously weaken the fore end. Those cuts will determine where the back edge of your cap will mate to the wood. 

3.Using the cap outline and length as reference lines, remove the wood between. That will be the first stage of wood removal. 

4. The first stage of wood removal has left the outside dimensions of the cap when installed. Now measure down from the flats of the end plate to the curvature of the inner surface of the cap to determine the shape of the wood that will be left when the cap is installed. In this second stage of wood removal, mark lines the same depth down from the bottoms of the barrel channel flats (a dial caliper is a good measuring tool for this). That will give you references as to where to draw the outline of the end plate where it fits under the barrel (Fig.9). Alternatively, you can make a template of the end cap and use it to make the outline for stage two. In either case, make sure that the flats of the end plate and the flats of the barrel channel line up closely. 

5.Carefully remove the wood back to the saw cuts described in Step 2 (the wood will be getting pretty thin). At this stage, the muzzle cap should start to slide onto the wood. Coat the inside of the cap with inletting dye, grease, lipstick or other visible indicator. Slide the cap on until resistance is felt, remove and carefully file off any marks from the wood. Repeat fit and file until the cap slides on back to the shoulder and does not rock from side to side. 

6.Coat the rear edge of the cap with inletting dye. With the barrel and cap in place, give a gently tap on the front end of the cap and remove it. Shave off any black marks on the shoulder, removing little slivers of wood until you get a close fit all the way around (Fig. 10). 

7.Even if you have doing a good job of fitting, the wood encompassed by the cap is thin and fragile. It needs to be reinforced.  The old timers used hide glue. Epoxy barrel bedding compound is much better (see suppliers). Coat the inside of the cap and the barrel with release agent if you want to be able to remove it later. If you want to do a permanent installation, Keith suggests that the inletting black, lipstick etc. should be removed with Acetone or Brake Drum Cleaner on a rag, wiping the surface clean prior to applying the AcraGlasTM or other epoxy bedding. If you have access to a bead-blasting cabinet, give the inside of the cap a light treatment; a light sanding with 220 grit sandpaper will also improve bonding. Coat the barrel with release agent or paste wax. You don’t want the barrel to be permanently fixed to the cap.Fill the cap with an excess of bedding compound to prevent voids. Slide the cap onto the wood, clamp the barrel into place for proper alignment and give a few gentle taps on the end plate to make sure it is seated against the shoulder. The compound should squeeze out all around. Keith pulls the cap back firmly to the shoulder and up against the barrel using a combination of rubber bands and A-frame clamps (Fig.11).

8.After the compound has set up, turn the assembly upside down with the corner of the butt plate on a solid surface. Tap the butt against the surface and the barrel will lever itself out of its channel. 

9.Anchor the cap into place using a small flat head machine screw; a 2-56 or 3-48 works fine (Fig. 12a, 12b). I have made soft copper rivets from 2 gauge electrical wire. They work fine, but it is awkward holding the stock in place (sans barrel) when riveting. The underside of the barrel can serve as the “anvil” when peening the rivet on the cap outside. When you peen the rivet on the inside of the cap, make sure you have a firm support under the rivet on the outside. Keith Lisle is better in this than I am; he will describe his procedure in detail in Part II of this series

10.Finally, level the ramrod groove to eliminate any “step” between the bottom of the groove and the underside of the cap. When replacing the ramrod, you want a flawless smooth entry ramp into the thimbles.

    Installing a commercial cap takes time and patience even if you have the proper cap-to-barrel fit. But what if your muzzle dimensions fall between increments of commercially available caps (as swamped or tapered custom barrels tend to do)?  One size is too small, the next size up is too big, so you are left to make your own. Part II will describe making a cap that is custom fit to your barrel. 

Acknowledgment

Thanks to Keith Lisle (Custommuzzleloaders.com) for his helpful suggestions and to John Cummings for his impeccable editing. 

Suppliers

Brownell’s Inc., 800-741-0015, Brownells.com, for Hi-Force 44 low-temp silver solder, AcraGlasTM epoxy bedding and a wide range of gunsmithing materials.

Track of the Wolf (trackofthewolf.com/List/Item.aspx/800/1) for a wide range of sheet metal and cast muzzle caps

References

1.Alexander, Peter A. The Gunsmith of Grenville County. Scurlock Publishing Co., Texarkana, TX, 2002.

2.Buchele, William, George Schumway and Peter Alexander. Recreating the American Longrifle. G. Schumway, Publisher, York, PA 1999.

3.Gusler, W.B. and J.D. Lavin. Decorated Firearms 1540-1870. The Colonial Williamsburg Foundation, Williamsburg, VA, 1977.

4. Wolf, Erhard. Steinschloss-Jägerbüchsen. DWJ Verlag CmbH Publishers, Blaufelden, Germany, 2006.

5.Hanson III, Charles E. Trade Gun Sketch Book. Track of the Wolf, Osseo, MN, 1978.

This article was featured in Muzzle Blasts Magazine in November 2017

NMLRA.org

Muzzle Blasts on Instagram
NMLRA on Facebook

NMLRA on Youtube

Muzzle Blasts Podcast



How to Load a Muzzleloader

We wanted to bring this illustration out from the Muzzle Blasts Magazine archives. Commissioned in 2015, we’d like to thank Larry Small for illustrating this great diagram.

IMG_1983.jpeg

How to load a Muzzleloader

  1. Make sure the bore is dry by using a ramrod with a cleaning jig and a clean, dry patch.

  2. With the hammer down for safety, clean the frozen, pan, and flint (watch out for the sharp edges of the flint). Be sure the flash hole is clear of obstruction by inserting a vent pick, paper clip, or pipe cleaner. Load a flintlock with the frizzen and hammer all the way forward.

    1. For a percussion firearm, inspec the nipple for obstruction by using a nipple pick or paper clip. With an unloaded firearm, snap a cap or two. Always point the muzzle in a safe direction.

  3. Pour the powder from a powder horn or flash into a measure. For safety, never pour powder directly into the bore from a horn or flask.

  4. Pour the measured powder charge down the bore. Avoid placing your hands or face directly over the muzzle.

  5. Center a lubricated or moistened patch over the bore and place the lead ball onto the patch.

  6. With the short end of a short starter, set the patched ball into the bore. Use the Pam of your hand to press the ball into the muzzle.

  7. Push the ball deeper with the long end of the short starter by using the palm of your hand.

  8. Firmly seat the load against the powder charge by using short strokes with your ramrod. NEVER fire a muzzleloader if the ball is not firmly seated on the powder charge.

  9. Use a pencil to make a reference mark on your ramrod when the lead ball is correctly loaded.

  10. Remove the ramrod and store it under the barrel.

  11. For a flintlock, fill the pan 1/4 to 1/3 full of priming powder, place the hammer into the half- cock position, and close the frizzen. When ready to shoot, bring the hammer into full cock position.

    1. For a percussion muzzleloader, bring the hammer into the half-cock position and place a cap firmly onto the nipple. When ready to shoot, place the hammer at full cock.

  12. Be certain of your target and what lies beyond. Aim and fire.

  13. Run a damp cleaning patch down the bore and begin the process again, no need to repeat step #9

The Muzzle Blasts Podcast is now available on Apple Podcasts

We’re very excited about another step forward for the NMLRA, our new podcast is now live on Apple Podcasts, the largest Podcast platform in the world! Be sure to subscribe to us on apple podcasts if that’s where you get your podcasts. If not, don’t fret, we’re also on Spotify, Google podcasts, and more.

The Romance of the Smoke -Longhunter Record Breaking Pronghorn with Eric Stanosheck

We’re excited to announce a new episode of the Muzzle Blasts Podcast this week. For this episode, we’re talking to big game hunter and Longhunter Society Record holder Eric Stanoschek about his record-breaking pronghorn trophy.

EStanoschek_Pronghorn_004A.png

 In this episode, Eric recounts this record-breaking pronghorn hunt, but also his history with modern high power rifles and his eventual conversion to hunting exclusively with muzzleloaders.

For Eric there is something special about the one-shot challenge of muzzleloader hunting, he calls it “The Romance of the Smoke”.  This love of hunting and muzzleloaders runs in his family, three of his four kids and his wife hunt with muzzleloaders.

We're excited to announce a new episode of the Muzzle Blasts Podcast this week. For this episode, we're talking to big-game hunter and Longhunter Society Record holder Eric Stanoschek about his record-breaking pronghorn trophy. In this episode, Eric recounts this record-breaking pronghorn hunt, but also his history with modern high power rifles and his eventual conversion to hunting exclusively with muzzleloaders.

 Having hunted with muzzleloaders since the early 2000s, Eric has gone on 66 big game hunts and has 42 animals recorded in the Longhunter Society program.

  For him, hunting and using Muzzleloaders is about the relationship with the gun. Unlike modern firearms, muzzleloaders can be a little tricky, and that’s what Eric likes. He says, “For me, hunting with a muzzleloader is about how close I can get and how much time do I get to spend with the animal.”

Muzzleloading Instructor Course with Klint Macro - June 2020

We have scheduled another Muzzleloading Instructor Course with Klint Macro of the Trigger Pressers Union June 10, 11, and 12, 2020!

In these classes, Klint Macro focuses on working with each and every student to fully understand the NMLRA/NRA Muzzleloading Instructor Course curriculum. You’ll walk away with some great knowledge and the confidence to safely share your love of muzzleloading.

You can register for the class at the NRA website or by contacting Klint directly.

1.jpg

Recording 75 years of NMLRA History | A conversation with Author Thomas Schiffer

Mr. Schiffer and his camera have been a staple of NMLRA Events for decades now, but in his latest book, he reaches back in time to unearth and organize photos, documents, and stories from the NMLRA's beginnings in the 1930s.

The NMLRA on Shooting USA! Tonight on the Outdoor Channel!

Tonight! Thank you Jim Scoutten's Shooting USA for featuring us on tonights episode!

(AmmoLand.com)- We’re slowing things down for Muzzle Loading in Friendship, Indiana at the National Muzzle Loading Rifle Association’s Nationals. It’s one part competition and one part living history from the 1820s. And we’ve got George Sutton – Mr. Flintlock from Impossible Shots – as our guide to the people and the competition that draws folks to black powder.

38-12-1-720-600x338.jpg

Plus, the long story of the 1911s that are now History’s Guns.

Then, John reports from Hollywood with the cowboy guns from the movies.

And JP shows you how to choose and set your zero. More Info…

38-12-4.jpg

USA AIR TIMES
Wednesday 9:00 PM Eastern and Pacific, 8:00 PM Central on Outdoor Channel
Shooting USA is listed as a one-hour show in your cable menu.

AND NOW IN CANADA
On the New Sportsman Canada Channel
Our Same Show, the Same Week, as in the USA

Sportsman Canada Channel is available in 750,000 Canadian Households.  Find the channel and find us north of the Border.

Subscribe to see all shows as often as you like at www.ShootingUSA.com

Jim
Defending the 2nd by Example in the 26th Year

Muzzle Blasts is Growing - Exciting new announcments from the NMLRA

Muzzleloading and Living History aren’t dying, they are evolving.

We’ve been publishing “Muzzle Blasts” magazine in one form or another since 1930. Muzzle Blasts is the Original MuzzleLoading, Traditional craft, and Living History Magazine. Delivered to your door or email every month, each issue is packed with content about muzzleloader shooting sports, living history, traditional craft, tutorials, stories, and accouterments.

To expand on the quality Muzzle Blasts delivers each month, the NMLRA has launched a new media initiative to bring you more of what you love.

We’re going to take you inside events and classes like you’ve never seen, and we are able to do all of this thanks to the members of the NMLRA.


New Platforms

We are excited to share the launch of the "Muzzle Blasts" Podcast, a new radio-like show from the NMLRA where we meet with all sorts of known and unknown people in the world of Living History.

In our first episode, we were excited to sit down with a representative from Goex Powders and Deer Creek Products to discuss the evolving world of Muzzleloading.

With aging members, many in the muzzleloading and living history communities are worried about the future of the sport. We sit down with Anita Vincenti from Goex Powder and Jim Christie of Deer Creek Products to discuss the future of muzzleloading and why it's not dying, it's evolving.

We Love Muzzle blasts

We know you love Muzzleblasts Magazine, and we want to bring you more of what you love each week.

Our dedicated Media Team will be covering not NMLRA events and classes, but muzzleloading and living history events across the country to show you that Living History is not dying, it’s evolving.

Muzzle Blasts on Social Media

We’re bringing daily updates from the world of the NMLRA to you through social media. We love hanging out around the campfire with our friends during an event, but now we can hangout everyday! With the NMLRA’s new media efforts we are bringing you the quality of Muzzleblasts right to your phone, tablet, or computer each day.

Follow the NMLRA on Facebook

Follow Muzzleblasts on Instagram

Follow the Longhunter Society on Instagram

The NMLRA on Pinterest

Gallery Block
This is an example. To display your Instagram posts, double-click here to add an account or select an existing connected account. Learn more